Page History

Top-fuel dragsters like the one shown above accelerate from rest at a tremendous rate.  They race on a straight 1/4 mile long track.  From a standing start, they complete the quarter mile in about 4.5 seconds and reach a speed of about 330 mph by the finish line.  

h2. Part A

Show that the statistics given in the problem introduction are inconsistent at the 10% level with the assumption that the dragster produces constant acceleration as it moves down the track.

System:  Dragster as [point particle].

Interactions:  External influence from the ground (friction) assumed to produce constant acceleration.

Model:  [One-Dimensional Motion with Constant Acceleration].

Approach:  We are asked to prove that the model we are examining _does not_ fit the data.  To do so, we look for a contradiction.  In this case, we have several ways to find the acceleration, since we have a large number of givens.  Choosing our coordinates such that the race begins at _x_~i~ = 0 and proceeds in the positive _x_ direction, we have:

{panel:title=Givens}{latex}\begin{large}\[ t_{i} = 0\]\[t_{f}=\mbox{4.5 s}\]\[ x_{i} = 0\]\[x_{f} = \mbox{402 m} \]\[v_{i}= 0\]\[v_{f} = \mbox{148 m/s}\]\end{large}{latex}{panel}

We now have three separate paths to find the acceleration _a_.  First, we can use:

{latex}\begin{large}\[ v_{f} = v_{i} + at \]\end{large}{latex}

to give:

{latex}\begin{large}\[ a = \frac{v_{f}}{t} = \mbox{33 m/s}^{2}\]\end{large}{latex}

Next, we can use:

{latex}\begin{large}\[ x_{f} = x_{i} + v_{i}t + \frac{1}{2}at^{2} = \frac{1}{2}at^{2}\]\end{large}{latex}

to give:

{latex}\begin{large}\[ a = \frac{2x_{f}}{t^{2}} = \mbox{40 m/s}^{2}\]\end{large}{latex}

Finally, we can use:

{latex}\begin{large}\[ v_{f}^{2} = v_{i}^{2} + 2a(x_{f}-x_{i}) \]\end{large}{latex}

to give:

{latex}\begin{large}\[ a = \frac{v_{f}^{2}}{2x_{f}} = \mbox{27 m/s}^{2}\]\end{large}{latex}

These accelerations differ from each other by more than 10%, so we conclude that the model is inconsistent at the 10% level.

h2. Part B  

Using the fact that a top-fuel dragster will typically weigh 2200 lbs, show that the assumption that the dragster moves down the track with a constant value for the power delivered to the car in the form of kinetic energy _is_ consistent at the 10% level.

System:  Dragster as [point particle].

Interactions:  Friction interacts with the dragster in such a way as to deliver constant power to the dragster's kinetic energy.

Model:  [Mechanical Energy and Non-Conservative Work].

To show that the model is consistent, we need two ways to find the power that rely on different subsets of the given information.  The most straightforward way to find the power is to use the velocity and the time, since the Law of Change for our model is:

{latex}\begin{large}\[ E_{i} + W^{NC} = K_{i} + P^{NC}\Delta t = K_{f}\]\end{large}{latex}

Thus, we can write:

{latex}\begin{large}\[ P^{NC} = \frac{\frac{1}{2}mv_{f}^{2}}{\Delta t} = 5.35\times 10^{6}\mbox{ W} = \mbox{7200 hp}\]\end{large}{latex}

We have so far used the time and the velocity information, but we have not yet used the fact that the race is 1/4 mile long.  To bring in distance information, we must perform an integral.  From the definition of [power], we know that we can write:

{latex}\begin{large}\[ P^{NC} = F^{NC}v \]\end{large}{latex}

where _v_ is the speed of the dragster.  This equation can be integrated using a useful trick.  

{note}The trick we are about to use is one that might serve you well in other problems.{note}

If we use the fact that the non-conservative force is equal to the net force on the dragster in this case, we can write:

{latex}\begin{large}\[ P^{NC} = mav = m\frac{dv}{dt}v \]\end{large}{latex}

we can now use the chain rule to write:

{latex}\begin{large}\[ \frac{dv}{dt} = \frac{dv}{dx}\frac{dx}{dt} = \frac{dv}{dx} v\]\end{large}{latex}

This gives us the integrable equation:

{latex}\begin{large}\[ P^{NC} dx = mv^{2} dv \]\end{large}{latex}

giving:

{latex}\begin{large}\[ P^{NC} (x_{f}-x_{i}) = \frac{1}{3}m(v_{f}^{3} - v_{i}^{3}) \]\end{large}{latex}

{info}This equation might be considered to express "the kinematics of constant power" as opposed to the kinematics of constant force that we have spent so much time learning.{info}

We can now express the power in terms of the distance traveled and the velocity gained:

{latex}\begin{large}\[ P^{NC} = \frac{mv_{f}^{3}}{3x_{f}} = 5.9\times 10^{6}\mbox{ W} = \mbox{7900 hp}\]\end{large}{latex}

which is consistent with our previous answer at the 10% level.

{tip}It is usually true for real-worldthat when attempting to maximize _acceleration_, that the motion is power-limited.  This is why sports cars laud their horsepower ratings.  Maximal _Brakingbraking_ however, is usually better described by motion with constant acceleration.{tip}

{info}The upshot of this is that although these dragsters' engines _deliver_ over 7000 hp (over _twenty times_ the rated horsepower of a production sports car) the car's performance is still effectively power limited.  The capacity of friction to produce acceleration is _not_ the limiting factor.  (If you considered the values obtained for the average acceleration in Part A, this should come as something of a surprise.){info}