When a ball is started out with a purely sliding motion on a slick surface like a bowling alley, it will gradually begin to rotate until eventually (if the lane is long enough) it is rolling without slipping. Suppose a bowling ball which is effectively a solid sphere with a diameter of 22 cm and a mass of 6.0 kg is started down a perfectly level alley with a coefficient of kinetic friction equal to 0.10. The ball is initially sliding with no rotation and is moving at a rate of 2.8 m/s. How fast will the center of mass of the ball be moving along the alley when it is rolling without slipping?
Composition Setup
Solution
We will solve the problem via three different methods.
Deck of Cards
id
bigdeck
Wiki Markup
When a ball is started out with a purely sliding motion on a slick surface like a bowling alley, it will gradually begin to rotate until eventually (if the lane is long enough) it is rolling without slipping. Suppose a bowling ball which is effectively a solid sphere with a diameter of 22 cm and a mass of 6.0 kg is started down a perfectly level alley with a coefficient of kinetic friction equal to 0.10. The ball is initially sliding with no rotation and is moving at a rate of 2.8 m/s. How fast will the center of mass of the ball be moving along the alley when it is rolling without slipping?
Solution: We will solve the problem via three different methods.
h4. Method 1
System: The ball as a [rigid body] subject to external forces of gravity, normal force and kinetic friction.
Model: [Constant Angular Momentum].
Approach: In this case, the most direct (but probably not the most obvious) method of solution is to consider the angular momentum about an axis fixed at some point on the alley surface. For simplicity, we select the point at which the ball is released. By taking a point on the alley surface, we have guaranteed that there is zero net torque acting on the system (the ball) about this axis. Gravity and the normal force each create a nonzero torque, but they balance each other perfectly because they share the same [lever arm] and they have the same magnitude. The friction force produces no torque because it has zero lever arm.
PICTURE OF LEVER ARMS
{note}If it is not apparent to you that the force of gravity and the normal force acting on the ball have equal magnitudes, you should write Newton's 2nd Law for the y-direction.{note}
The [angular momentum] of the ball about the axis we have chosen can be broken into two parts by considering the contribution of the translation of the ball's center of mass and the rotation of the ball about its center of mass.
{latex}
Card
label
Method 1: Angular Momentum
Method 1: Angular Momentum
Toggle Cloak
id
sys1
System:
Cloak
id
sys1
The ball as a .
Toggle Cloak
id
int1
Interactions:
Cloak
id
int1
External forces of gravity, normal force and kinetic friction.
Toggle Cloak
id
mod1
Model:
Cloak
id
mod1
.
Toggle Cloak
id
app1
Approach:
Cloak
id
app1
Toggle Cloak
id
diag1
Diagrammatic Representation
Cloak
id
diag1
We begin with a free body diagram. Since this problem will deal with rotation, we must also select an axis of rotation.
Image Added
In this case, the most direct (but probably not the most obvious) method of solution is to consider the angular momentum about an axis fixed at some point on the alley surface. For simplicity, we select the point at which the ball is released. By taking a point on the alley surface, we have guaranteed that there is zero net torque acting on the system (the ball) about this axis. Gravity and the normal force each create a nonzero torque, but they balance each other perfectly because they share the same moment arm and they have the same magnitude. The friction force produces no torque because it has zero lever arm.
Image Added
Note
If it is not apparent to you that the force of gravity and the normal force acting on the ball have equal magnitudes, you should write Newton's 2nd Law for the y-direction.
Cloak
diag1
diag1
Toggle Cloak
id
math1
Mathematical Representation
Cloak
id
math1
The angular momentum about a single axis of the ball about the axis we have chosen can be broken into two parts by considering the contribution of the translation of the ball's center of mass and the rotation of the ball about its center of mass.
{latex}
h4. Method 2
System: The ball as a [rigid body] subject to external forces of gravity, normal force and kinetic friction.
Model: [Point Particle Dynamics] and [Angular Momentum and Torque] plus [One-Dimensional Motion with Constant Acceleration|1-D Motion (Constant Acceleration)].
Approach: We can also approach this problem by the standard technique of treating the linear dynamics of the center of mass and the rotational dynamics of the ball about its center of mass separately. The free body diagram is:
FREE BODY
Thus, Newton's 2nd Law takes the form:
{latex}\begin{large}\[ - F_{f}= ma_{x}\]\end{large}{latex}
and its angular counterpart is:
{latex}\begin{large} \[ F_{f}R = I\alpha \] \end{large}{latex}
The trouble is that these equations do not involve the speed of the ball. One way to bring the speed in is to use kinematics. We know that:
{latex}\begin{large}\[ v_{x,f} = v_{x,i} + a_{x}t \]\[ \omega_{f} = \omega_{i} + \alpha t\]\end{large}{latex}
Using the fact that ω~i~ = 0 and ω~f~ R = _v_~x,f~ and substituting for _a_~x~ and α using the equations we wrote above, it is possible to put these equations in the form:
{latex}\begin{large}\[ v_{x,f} = v_{x,i} - \frac{F_{f}}{m} t \] \[ v_{x,f} = \frac{F_{f}R^2}{I} t \] \end{large}{latex}
Eliminating _t_ from the equations gives:
{latex}\begin{large}\[ v_{x,f}(1+\frac{I}{mR^{2}}) = v_{x,i} \]\end{large}{latex}
{tip}The same answer as was obtained using method 1.{tip}
h4. Method 3
System: The ball as a [rigid body] subject to external forces of gravity, normal force and kinetic friction.
Model: [Work-Energy Theorem] and [One-Dimensional Motion with Constant Acceleration|1-D Motion (Constant Acceleration)].
Approach: Often when a speed is required, energy is an efficient way to obtain the answer. In this particular problem, angular momentum is a much faster route, but it is instructive to consider the form of the energy equations.
As the ball rolls along the alley, gravity and the normal force are perpendicular to its linear movement and so they do no work that would affect the ball's linear velocity. They also exert no torque about the center of mass, and so they do no work that would affect the ball's angular velocity. Friction, however, is anti-parallel to the ball's displacement and so it does negative work on the ball's rotational kinetic energy and it has a non-zero lever arm so it does work that acts to increase the ball's angular speed. The relevant forms of the work-energy theorem are:
{latex}\begin{large} \[ -F_{f}x = \frac{1}{2} mv_{f}^{2} - \frac{1}{2} mv_{i}^{2}\]
\[ F_{f}R\theta = \frac{1}{2}I\omega_{f}^{2} - \frac{1}{2}I\omega_{i}^{2}\]\end{large}{latex}
{warning}It is very important to recognize that mechanical energy is _not_ conserved in this problem. The ball is _not_ rolling without slipping, it is sliding and rotating. Thus, the friction is _not_ static and so it does dissipate some energy into heat.{warning}
Once again, we know that ω~f~ R = _v_~f~. We *do not*, however, know any relationship between _x_ and θ at this time. The ball _ends up_ rolling without slipping, giving the relationship between the final speeds, but it has certainly been slipping in the interim. Thus, the angular distance covered will not be directly related to the linear distance. To solve this problem, we must assume that the acceleration and angular acceleration are constant. In that case, we know from kinematics that:
{latex}\begin{large}\[ x = \frac{v_{f} + v_{i}}{2} t \] \[ \theta = \frac{\omega_{f} + \omega_{i}}{2} t\]\end{large}{latex}
Substituting these relationships gives:
{latex}\begin{large}\[ - F_{f} = m \frac{(v_{f} - v_{i})}{t}\]
\[ F_{f} R = I\frac{v_{f}}{Rt} \]\end{large}{latex}
Eliminating _F_~f~ (or _t_) then gives the same answer as was obtained via methods 1 and 2.
{info}It is instructive to note that the (negative) work done by friction on the linear kinetic energy is:\\
{latex}\begin{large}\[ -F_{f} x = -F_{f}\frac{v_{f}+v_{i}}{2} t \]\end{large}{latex}
while the positive work done on the angular kinetic energy is:
{latex}\begin{large}\[ F_{f}R\theta = F_{f} \frac{v_{f}}{2} t \] \end{large}{latex}
Clearly, the negative work is larger in magnitude, and we can see that the net energy dissipated to heat will be:
{latex}\begin{large} \[ |W_{\rm dissipated}| = F_{f} \frac{v_{i}}{2} t \] \end{large}{latex}
where _t_ is the amount of time elapsed from the instant the ball is released until the instant it begins to roll without slipping.
{info}
Cloak
math1
math1
Cloak
app1
app1
Card
label
Method 2: Dynamics
Method 2: Dynamics
Toggle Cloak
id
sys2
System:
Cloak
id
sys2
The ball as a .
Toggle Cloak
id
int2
Interactions:
Cloak
id
int2
External forces of gravity, normal force and kinetic friction.
Toggle Cloak
id
mod2
Model:
Cloak
id
mod2
Single-Axis Rotation of a Rigid Body, and One-Dimensional Motion with Constant Acceleration.
Toggle Cloak
id
app2
Approach:
Cloak
id
app2
Card
label
Method 3: Energy
Method 3: Energy
Toggle Cloak
id
sys3
System:
Cloak
id
sys3
The ball as a .
Toggle Cloak
id
int3
Interactions:
Cloak
id
int3
External forces of gravity, normal force and kinetic friction. Gravity is conservative while the normal force and friction are non-conservative.
Toggle Cloak
id
mod3
Model:
Cloak
id
mod3
Mechanical Energy, External Work, and Internal Non-Conservative Work, One-Dimensional Motion with Constant Acceleration and .
