Integrate Piston Cup Assembly
Rule: if you are not directly helping with integration, you must be dancing.
Pre-Assembly: Build the Firebolt Jumbo
FILL THIS OUT
Make sure you are using all appropriate PPE such as goggles and gloves!
- Take a DRILLED & TAPPED 1/8 NPT PLUG (which has a 1/4-20 hole drilled and tapped through the middle) and thread a FIREBOLT into it using approximately 3 wraps of TEFLON TAPE.
- Put two E-MATCHES through the hole in the 1/4-20 bolt and glue with 5 MINUTE EPOXY on the head end of the screw. You will need a POPSICLE STICK.
- On the other end of the screw, you may be able to push a small amount of epoxy on, but don't get it in the plug's threads.
- After the epoxy dries, put a preselected amount of BLACK POWDER in a little packet of BLUE TAPE, with the e-match head inside of the packet.
Pre-Assembly: Tender Descender Setup
- Take the two TENDER DESCENDER BODIES and put the appropriate amount of black powder in them.
- Close the bodies and thread a firebolt into each one, using approximately three wraps of Teflon tape.
Pre-Assembly: Pack the Main Parachute
- Take the MAIN PARACHUTE.
- Pack the main parachute into the DEPLOYMENT BAG.
Primary Integration Checklist
- Make sure that the PISTON rod is fully compressed (retracted).
- Integrate the 1/8TH NPT ELBOW FITTINGinto the piston inlet port that is closest to the blunt end. Use approximately three wraps of TEFLON TAPETeflon tape. Make sure that the male end of the elbow fitting is pointing downwards.
- Screw in the Jumbo Firebolt into the male end of the elbow fitting using approximately three wraps of Teflon tape
Screw the PAYLOAD BULKHEAD into the top of the piston using fourLENGTH HERE 3/4" LONG 1/4-28 BOLTS. You need a 3/16THS HEX KEY.
INSERT AVIONICS BAY INTEGRATION PROCEDURE HERE
Put the AVIONICS BAY COUPLER over the piston. The coupler's switchband should be closer to the side with the Firebolt screwed in.
Using four LENGTH HERE 1/2" 1/4-28 LOW PROFILE SCREWS screw in the AVIONICS BULKHEAD to the bottom of the piston. The milled face (mass saving cuts) should be internal to the Avionics Bay. Use the 3/16ths hex key again.
- Now it's time to assembly the cup including its contents, including soft goods such as WEBBING and chutes as well as eye nut, cotter pin, tender descenders, and more.
- Fully screw a 3/8-16TH NUT onto the piston. Slide the DIAPHRAGM onto the piston and screw in the 3/8-16TH EYE BOLT.
- INSERT INFORMATION ON USING LOCTITE
- Put the COTTER PIN in the eye nut.
- Put a 1000LB QUICKLINK on the eye nut. Don't close the quicklink yet.
- Now it's time to integrate the two TENDER DESCENDERS. Prepare yourself emotionally for this experience.Tender Descenders.
- Attach both Tender Descenders using one of the two KEVLAR LOOPSto the quicklink. The Tender Descenders should be in parallel. Consult this page for more information.
- Congrats! You've finished integrating the Tender Descenders.
- Screw the diaphragm into the CUP with FOUR 10-32 GRUB SCREWS using a 7/64 HEX WRENCH.
- Before closing that quicklink, make sure to also secure the TD safety wires to that quicklink. Add a 1500LB SWIVEL to this quicklink and then once this is done, secure the quicklink.
- Using the second kevlar loop, connect the other ends of the Tender Descenders. Secure another 1000LB QUICKLINK to this.
- Check the setup of the Tender Descenders thoroughly. Have somebody else check it, too.
- When routing the e-match wires to the Avionics bay D-sub, leave plenty of slack between the Avionics Bay Bulkhead and the Diaphgram (at least 5"). Feel free to secure with a small amount of blue tape.
- Off to the side, coil the booster to mission
- (Stand in step for CRIMP) Tie a piece of paracord to the eye nut. Tie a knot on the other end.
- NOTE ON HARDWARE REV: If the new eye nut is too large to put a quicklink around, consider milling the eye nut down, sewing a piece of webbing onto it, or otherwise just doing something more professional than "tie a piece of paracord."
- Secure a 1000lb quicklink to the paracord, followed by a 1500lb swivel and another quicklink.
- PROPOSED CHANGE FOR HARDWARE REV: See if you can't sew at least one line directly onto the swivel?
- POTENTIAL CHANGE: Perhaps everything should have its own swivel?
- Coil the booster–mission package webbing and stow in several small infinity wraps using minimal tape. The optimal height of the each infinity wrap is a little over 1". Leave enough slack (i.e. on one end (do not infinity wrap) on one side to extend the lines from the diaphragm to the forward closure.
- Once this is done, return to the 1500lb swivel you installed early and attach a 1000LB QUICKLINK to the other side.
- Attach the slack side of the booster -to mission package webbing to the at the diaphragm this outermost quicklink.
Attach both Tender Descenders in series - to the quicklink attachment point. Attach the drogue riser onto the second Tender Descender quicklink. For the time being, leave the line on the outside Screw the diaphragm into the CUP with FOUR 10-32 GRUB SCREWS using a 7/64 HEX KEY.
Everything you previously installed should be inside of the cup.
- Coil the main riser and stow in several small infinity wraps using minimal tape. Attach one side to a 1000LB QUICKLINK followed by a 1500LB SWIVEL followed by another 1000LB QUICKLINK and then the main parachute shroud lines.
- end of the main riser onto the quicklink attachment point. Attach the other end of the main riser using a 1000LB QUICKLINK to the packed main parachuteeye nut.
- Pack the coiled riser behind riser, followed by the shroud lines, and then the main parachute (towards the nose cone) inside of into the cup.
- PROPOSED CHANGE: Add a section on packing the main parachute before this.
- Attach the main deployment bag using some 2000LB KEVLAR LINE to the quicklink on the other side of the Tender DescendersPut the airframe tube over the assembly. You may need to move the drogue riser and mission package to booster webbing out of the way.cut using KEVLAR SHEARS.
- Using a setup of 880 LB QUICKLINK, 1500 LB SWIVEL, and then 880 LB QUICKLINK, attach the DROGUE riser to the top of the main deployment bag.
- Put the AIRFRAME TUBE over this complete assembly.
- "Struggle with clocking" - Jakob
- Screw in four 1/2" 8-32 SCREWS to attach the Airframe
“Struggle with clocking” - Jakob, 11:20am
- Attach the drogue riser to the packed drogue with a 220 lb quicklink. Coil and stow excess drogue line (if necessary) and pack everything into the booster section.
NOSE CONE with the right clocking to the other end of the Avionics Bay using four 8-32 SCREWS. - Attach Coil and stow excess mission package to booster webbing and secure with a small amount of painters tape. Place this in the booster section. Then attach the mission package to booster webbing to the forward closure the PSEUDO FORWARD CLOSURE with a 1000lb quicklink, 1000LB QUICKLINK followed by a 1500lb swivel, 1500LB SWIVEL and then another 1000lb quicklink 1000LB QUICKLINK.
- PROPOSED CHANGE FOR HARDWARE REV: See if you can sew it onto the swivel.
- PROPOSED CHANGE FOR HARDWARE REV: See if you can sew it onto the swivel.
- Pack Now, attach the other side of the mission package to booster webbing to the pseudo forward closure.
- Screw in the nosecone with the right clocking using four 8-32 screws.Place the drogue on top. The drogue should be as close to the separation point as possible.
- Put the mission package assembly on the booster extension coupler and secure with 3x with three 6-32 shear pins. For the Pathfinder vehicle, you will need to skip every other hole.
Notes from integration:
- Purchase 6x 8-32 grub screws
Materials:
Diaphragm
Piston (small)
1/8th NPT elbow fitting
Teflon tape
7/64 hex wrench
Payload bulkhead
Four LENGTH HERE 1/4-28 bolts
3/16THS Hex key
Avionics Bay Coupler
LENGTH HERE 1/4-28 screws
3/8-6TH nut
3/8-16TH eye bolt
Loctite
Cotter pin
Cup
Four 10-32 grub screws
plug
FireBolt XL
Avionics Bay (Coupler)
eye nut
- SHEAR PINS.Put a bit of tape over each shear pin.
Materials:
DRILLED & TAPPED 1/8 NPT PLUG (has a 1/4-20" hole tapped and threaded in the middle of it)
3x FIREBOLTS (a 1/4-20" bolt with a hole in the middle of it)
TEFLON TAPE
3x E-MATCH
5 MINUTE EPOXY
POPSICLE STICK
BLACK POWDER
BLUE TAPE
2x TENDER DESCENDER BODIES
MAIN PARACHUTE
DEPLOYMENT BAG
PISTON (the small one)
1/8TH NPT ELBOW FITTING
PAYLOAD BULKHEAD
4x 3/4" LONG 1/4-28 BOLTS
3/16THS HEX KEY
AVIONICS BAY COUPLER
4x 1/2" 1/4-28 LOW PROFILE SCREWS
AVIONICS BULKHEAD
WEBBING
3/8-16TH NUT
DIAPHRAGM
3/8-16TH EYE BOLT
LOCTITE
COTTER PIN
7x 1000LB QUICKLINKS (pack at least 4 extras)
2x KEVLAR LOOPS
4x 1500LB SWIVELS
CUP
4x 10-32 GRUB SCREWS
7/64 HEX KEY
2000LB KEVLAR LINE
KEVLAR SHEARS (the gray scissors)
2x 880LB QUICKLINKS
DROGUE
AIRFRAME TUBE
8x 1/2" 8-32 SCREWS
NOSE CONE
PSEUDO FORWARD CLOSURE
PACK OF 6-32 SHEAR PINScotter pin